Crossstitchforum - A FREE forum for Cross Stitchers

I have a chart (no sure how old) but it says they used Anchor reflecta 300 gold. I can’t really find this anywhere to purchase and I’m wondering if this is the old name for their current metallic thread? So does that mean I can buy any metallic thread?

I’ve seen there is a previous post on this forum back in 2018, similar question. Others suggested not to buy DMC metallic, and instead try Gutermann sulky, Kreinik or Glisson gloss - anyone who has experience with these like to suggest a safe bet?
This will be my first time using metallic thread.

I don't know how thick Reflecta was, but my go-to metallic thread is Rainbow Gallery's Petite Treasure Braid (or Kreinik's #4 Braid, which is pretty much identical to it). That is about the thickness of two strands of stranded cotton, I'd say, and I've always found it easy to work with (it's the metallic I used in the various rainbows for the word Hope)

I think the reflecta is the same thickness as one stranded cotton, because the chart says to use two strands of the gold for the main design, back stitch and French knots.

So from your suggestion, I could use the one strand of the rainbow gallery or kreinik instead?

Yes, or if you prefer a thinner thread doubled up, you could use Madeira GlissenGloss, which is about half the thickness of the two I mentioned and which is also easy to work with.

Great, thanks for your help Mabel

I might have some Reflecta. Let me check... (back soon...)

Alas. I have silver Reflecta, not gold. sorry about that. Don't be afraid of DMC. It's not my favourite by a long way, but if you only use relatively short lengths, it's beautiful once stitched.

Thank you Serinde for your help.
All these other threads can be confusing especially only looking online, I can’t appreciate how they look now that the non essential shops have closed.

I just needed to be sure that what I replace the reflecta with is a similar texture. It’s for a lucky cat pattern, the little gold piece that is in front of the cat

I can send the spool to you, if you'd like. Think of it as stash. If this sounds like a good idea, send me a pm with your address (and probably your name too lol).

Aw that’s so kind of you!
Only if you are sure, I’ve sent you a message with my details.

If I may, might I suggest that as it is your first time using metallic thread to try a few practice stitches on a small piece of aida?

Whichever thread you end up using, may I also suggest using shorter lengths of thread as they do have a tendency to fray.

Hope this helps.

That is a great point, I’ll be sure to try them first and keep the threads short.
I’m not great at French knots yet either, so I should try them out too with the metallic thread
Thank you Garnet

It's also helpful to loop the thread onto your needle. Start to thread your needle with a large loop of thread, but before you pull it all the way through, put the point of the needle through the loop. You can then adjust the thread by pulling on the long end. In effect, you are tying the slippery metallic thread to your needle. It does help!

Serinde wrote: ↑Sun Nov 08, 2020 10:52 am It's also helpful to loop the thread onto your needle. Start to thread your needle with a large loop of thread, but before you pull it all the way through, put the point of the needle through the loop. You can then adjust the thread by pulling on the long end. In effect, you are tying the slippery metallic thread to your needle. It does help!

I agree!! Works like a charm!!

I'm not sure what I'm getting myself into now

Serinde wrote: ↑Sun Nov 08, 2020 10:52 am It's also helpful to loop the thread onto your needle. Start to thread your needle with a large loop of thread, but before you pull it all the way through, put the point of the needle through the loop. You can then adjust the thread by pulling on the long end. In effect, you are tying the slippery metallic thread to your needle. It does help!

And if I stitch in 3 strands? One of the methods to anchor the thread at the beginning is to pull the needle with the thread through the fabric (on the wrong side, of course) and then to pull it through the "end" (at least through one strand of it).

Indeed, Lyudmila.